Translate the slicer-speak

FDM 3D-printing glossary

From brims to Z-banding: plain-English definitions for the terms that appear in profiles, manuals and troubleshooting threads.

FDM terms arranged around a nozzle and layer stack
AI-generated editorial illustration

A

Abrasive filament

Filament filled with hard particles such as carbon fibre, glass fibre, metal powder or some glow-in-the-dark pigments. It wears soft brass nozzles quickly, so makers usually recommend a hardened steel or similar wear-resistant nozzle. See hardened-steel nozzles.

B

Bed mesh

A grid of height measurements the printer takes across the build plate so the firmware can compensate for a bed that is not perfectly flat. It helps the first layer but does not fix a badly set Z offset.

Bowden extruder

An extruder mounted on the frame that pushes filament through a long PTFE tube to the hotend. It keeps the moving print head light, but the tube makes retraction and flexible filaments harder to tune than with direct drive.

Brim

A few extra loops printed flat around the base of a part to increase its contact area with the bed. It helps small or tall parts and warp-prone materials stay down, and is trimmed off afterwards. See warping and bed adhesion.

Bridge

A horizontal span printed in mid-air between two supported points. Short bridges usually print cleanly with good part cooling; long ones sag and may need supports or a design change.

Build plate

The surface the print sits on, often a removable steel sheet with a textured or smooth PEI coating. Each surface type grips materials differently, so check the maker's compatibility list.

C

Cold pull

A nozzle-cleaning method: heat the nozzle, push filament in, let it cool to a lower temperature and pull it out so debris comes out with the plug. Temperatures depend on the material and the printer maker's instructions.

D

Direct drive

An extruder mounted on the print head, right above the hotend. The short filament path gives more precise retraction and handles flexible filaments better, at the cost of a heavier moving head.

E

Elephant's foot

A first layer or two that bulges outwards beyond the part's walls, usually because the nozzle is too close to the bed or the bed is too hot. It matters on parts that must fit together.

Extrusion multiplier

A slicer setting that scales how much filament is pushed out. PrusaSlicer and Cura use similar ideas under different names; OrcaSlicer and Bambu Studio call it flow ratio.

F

FFF

Fused filament fabrication: printing by melting plastic filament and laying it down layer by layer. It is the same process people usually call FDM (a trademarked term).

Filament

The plastic feedstock for FFF printers, usually 1.75 mm diameter on current consumer machines and sold on spools by weight. Common types include PLA, PETG, ABS, ASA and TPU. See filament for functional parts.

Flow ratio

OrcaSlicer and Bambu Studio's name for the extrusion multiplier. Calibrate it per filament so top surfaces are neither gappy nor ridged.

G

G-code

The plain-text list of machine instructions (moves, temperatures, fan speeds) that a slicer produces and the printer runs. Some printers use their own packaged formats built on G-code.

Ghosting

Faint repeated ripples next to sharp features, also called ringing, caused by vibration as the print head changes direction. See layer shifts, ringing and Z-banding.

H

Heat creep

Heat travelling up from the hotend into the cold zone so filament softens too early and jams. It is more common with PLA in hot enclosures or when the hotend fan is failing.

Heat-set insert

A threaded brass insert pressed into a printed hole with a hot tip so the plastic melts and grips its knurling, giving durable machine-screw threads. See heat-set insert tools.

Hotend

The part that melts filament: the heater block, heater, temperature sensor, heat break and nozzle, plus its cooling fan.

I

Infill

The internal fill pattern inside a part's walls. More infill adds weight and print time; for strength, extra walls often help more. See supports, infill and walls.

Ironing

An optional final pass where the hot nozzle runs over the top surface with very little extrusion to smooth it. It adds time and suits flat tops.

J

No common term in this edition.

K

No common term in this edition.

L

Layer height

The thickness of each printed layer. Thinner layers show less stepping on curves but take longer; a common rule of thumb keeps it well below the nozzle diameter.

Layer shift

A sudden sideways offset part-way up a print, usually caused by the print head hitting something, a slipping belt or pulley, or skipped motor steps.

Line width

The width of each extruded line. It is often set around the nozzle diameter and can be a little wider for stronger walls.

M

Maximum volumetric speed

The most plastic, in cubic millimetres per second, that a hotend can melt reliably for a given filament. Printing faster than this causes under-extrusion.

N

Nozzle

The small tip the molten plastic leaves through. 0.4 mm is the common default; brass is standard and hardened steel resists abrasive filaments.

O

Overhang

A part of the model that leans out beyond the layer below. Gentle angles print without help; steeper ones droop and need supports or reorientation.

P

Perimeter

An outline wall of a layer (also called a wall or shell). More perimeters usually make parts stronger.

Pressure advance

A firmware feature (called linear advance in Marlin) that anticipates pressure in the nozzle so corners and line ends are cleaner. It is calibrated per filament.

Q

No common term in this edition.

R

Raft

A thick disposable base printed under the part. It is rarely needed on modern flat, levelled beds, but can help some awkward parts.

Retraction

Pulling filament back slightly before a travel move to reduce oozing and stringing. Too much can cause jams. See how to fix stringing.

S

Seam

The visible spot where each perimeter loop starts and ends. Slicers can align, hide in corners or randomise it.

Slicer

Software that turns a 3D model into G-code, for example OrcaSlicer, PrusaSlicer, Bambu Studio or UltiMaker Cura. See OrcaSlicer vs PrusaSlicer vs Cura.

Stringing

Fine plastic hairs between parts of a print, from molten plastic oozing during travel moves. Wet filament, high temperature and retraction settings are common causes. See how to fix stringing.

Support interface

The top layers of a support structure that touch the part. Denser interfaces give a better underside finish but are harder to remove.

T

Temperature tower

A calibration print that changes nozzle temperature in steps up its height so you can pick the best temperature for a filament.

Thermal runaway

A firmware safety check that shuts the heaters off if temperature readings stop responding as expected, for example if a sensor falls out. Never disable it.

Tolerance

The clearance you design between parts that must fit together. The right gap depends on the printer, material and orientation, so print a test fit first. See design tolerances and orientation.

Travel move

A movement where the nozzle moves without extruding. Slicers can avoid crossing perimeters to reduce stringing and marks.

U

Under-extrusion

Too little plastic coming out, seen as gaps, thin walls or weak layers. Causes include a partial clog, wet or tangled filament, low temperature or printing too fast. See under-extrusion and clogged nozzles.

V

No common term in this edition.

W

Warping

Corners lifting off the bed as the plastic cools and shrinks. ABS and ASA are most prone. See warping and bed adhesion.

X

No common term in this edition.

Y

No common term in this edition.

Z

Z-banding

Regular horizontal lines across a print's sides, often from Z-axis mechanics or layer-to-layer extrusion changes. See layer shifts, ringing and Z-banding.

Sources